EX-1183HMVS-2
4 Ports USB 3.2 Gen 1 Metal HUB with 15KV ESD Surge Protection
The rugged industrial-grade EX-1183HMVS-2 is a USB 3.2 Gen 1 metal hub for up to four end devices. The hub provides four bolt-on USB 3.2 Gen 1 downstream ports with 15KV ESD surge protection. It supports SuperSpeed USB 3.2 Gen 1 data transfer rate of up to 5Gbps and is backward compatible to USB 1.1. The included USB 3.2 Gen 1 cable can be attached to the EX-1183HMVS-2 with thumbscrews without a screwdriver. The EX-1183HMVS-2 can be powered via a DC Jack as well as a two-wire terminal block connector (+7V to +48V). The HUB meets the special requirements of industrial applications. Thanks to its special housing, the EX-1183HMVS-2 can be screwed to the wall, under a table or in a 19" cabinet (optional with EX-6099).
USB 3.2 Gen 1 Metal HUB with 4 Ports
15KV ESD Surge Protection for all 4 Ports
Protection of Devices against voltage fluctuation
Power +7V up to +48V DC over the DC-Connector or Terminal Block
Power supply optionally also from the USB-Bus +5V (Bus-Power)
Metal housing for wall, table or optional DIN-Rail (EX-6099)
Automatic recognition of the data transfer rate for the attached external devices
Supports 1.5A power for each output simultaneously (see detailed description on page 2)
Supports BC v1.2: SDP/CDP/DCP Charging Modes
Automatic detection of input polarity on the current terminal block
Rugged Metal Case
1x LED Power-Indicator
Two internal jumpers for individual mode control (data and power):
Bus power jumper:
ENA = bus power operation possible
DIS = operation with power supply only (self power)
Host control jumper:
ON = Power supply independent of host PC
HOST = Power supply only when host PC is switched on
Packaging Contents:EX-1183HMVS-2, Power Supply (12V/3A), USB 3.2 Gen 1 Cable, Manual
EX-11290HMS
10-Port USB 3.2 Gen 1 Metal HUB for table, wall and DIN-Rail, 15KV ESD Protection
The rugged, industrial-grade EX-11290HMS is a USB 3.2 Gen 1 metal HUB for up to ten end devices that can be installed on the wall or on a mounting rail. The EX-11290HMS ensures secure data transmission and a performance of up to 5Gbit/s. The EX-11290HMS is also equipped with 15KV ESD overvoltage protection. A maximum of 1.0A is available at nine USB ports via the external power supply, while up to 2.4A is available at one port.Power is supplied via the supplied plug-in power supply unit or an optional DIN rail power supply unit (self-power). Bus power is not supported.
USB 3.2 Gen 1 Metal HUB with ten downstream ports
15KV ESD surge protection for each output
Power +9V up to +24V DC via Terminal Block or DC-Connector
10 ports with 9x 1A and 1x 2.4A (total 57W) with the supplied power supply
Can also be used as a USB charger without connection to the host PC
Automatic recognition of the data transfer rate for attached peripherals
Includes wall mount kit and DIN-Rail Kit
Compact industrial design with a robust metal case
LED indicators for power supply and connection status
Chipset: VIA VL817Q7S
Packaging contents:EX-11290HMS, USB 3.2 Gen 1 cable 2.0m, power supply 12V/5A, DIN-Rail Kit, Wallmount Kit, Manual
EX-11237HMS-2
7-Ports USB 3.2 Gen 1 Metal HUB for Table, Wall and DIN-Rail, 15KV ESD Protection
The rugged, industrial-grade EX-11237HMS-2 is a USB 3.2 Gen 1 metal hub for up to seven end devices that can be wall-mounted or DIN-Rail mounted. It provides secure data transfer and performance of up to 5Gbps. The EX-11237HMS-2 is also equipped with 15KV ESD surge protection. A maximum of 2.4A can be made available per USB port via the external power supply.Power is supplied via the supplied plug-in power supply unit or an optional DIN-Rail power supply unit (self-power). Bus power is not supported.
USB 3.2 Gen 1 metal HUB with seven downstream ports
15KV ESD overvoltage protection for each output
Power supply +9V to +24V DC via terminal block or DC socket
2.4A per port with included power supply unit
Automatic detection of the data transfer rate for the connected peripherals
Includes wall mounting bracket and DIN-Rail kit
Compact industrial design with a robust metal casing
LED indicators for power supply and connection status
Chipset: VIA VL817S
Packaging contents:EX-11237HMS-2, USB 3.2 Gen 1 cable 2m, plug-in power supply unit 12V/5A, DIN-Rail kit, wall mounting kit, manual
EX-1177HMV
7 port USB 2.0 Metal HUB for DIN-Rail, Cable can screw lock
The rugged, industrial-grade EX-1177HMV USB hub with seven screw-lockable USB 2.0 outputs can be installed on the wall or on a support rail. It connects to a computer or server with the included USB 2.0 cable. It supports Hi-Speed USB 2.0 data transfer rate of up to 480 Mbps and is backward compatible to USB 1.1. It can be powered with USB bus power or via a two-wire terminal block connector (+7V to 24V).
USB 2.0 HUB with seven screwable downstream USB 2.0 ports
Power supply +7 to +24V DC via terminal block
User-friendly installation with the integrated DIN-Rail Kit
Compact industrial design
Automatic detection of the data transfer rate for the connected peripheral devices
Power supply optionally from USB-BUS +5V (Bus-Power)
Chipset: Terminus FE 2.1
Internal jumper for individual control of power supply:- ENA = bus power operation possible- DIS = operation with power supply only (self power)
Packaging contents:EX-1177HMV, USB 2.0 cable 2.0m, DIN-Rail Kit, Manual
Video
EX-1315IS
Dockingstation USB 3.2 Gen 1 to 1x RS-232 Surge & Isolation, LAN 1Gbps and 2x USB 3.2 Gen 1
The EX-1315IS USB 3.2 Gen 1 Docking Station provides one RS232 serial port with surge protection and isolation, one Ethernet 10/100/1000Mbps port and two USB 3.2 Gen 1 ports. Easy installation means there is no need to open the computer and the EX-1315IS can be installed while the computer is running.
Serial RS-232
Interface: RS232 V.24
15KV ESD Surge Protection
2.5KV Isolation
16C550 FIFO buffer with 16 bytes
I/O addresses and interrupt assigned by operating system
Data bits: 7, 8
Stop bits: 1, 1.5, 2
Parity: none, even, odd, space, mark
Signal RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
USB Bus powered
Ethernet
Compatible with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Supports IEEE 802.3az (Energy Efficient Ethernet)
Supports cross-over detection and auto-correction
Supports „Wake-on-LAN“ / LED indicator
USB 3.2 Gen 1 (formerly USB 3.0 / USB 3.1 Gen 1)
Supports USB 1.1 to 3.2 compatible peripheral devices
Power from the USB Bus (Bus Power) or Power Supply (Optional)
Packaging contents:EX-1315IS, Power Supply 12V/3A Driver CD, DIN-Rail Kit, Manual
EX-11244HMS
4 Port USB 3.2 Gen 1 metal HUB with 15KV ESD Protection for wall and DIN-Rail mounting
The robust, industrial-grade EX-11244HMS USB hub in a metal housing with four USB 3.2 Gen 1 outputs can be installed on the wall or on a carrier rail. It ensures secure data transfer and excellent performance of up to 5Gbps (SuperSpeed USB 5Gbps). In addition, EX-11244HMS is equipped with 15KV ESD surge protection. Up to 1.5A can be provided to each port via the external power supply. This allows you to charge iPhone, iPad, smartphone and tablet without any problems.An optionally available power supply is required for operation (self-power), bus-power is not supported.
USB 3.2 Gen 1 Metal HUB with four downstream ports
15KV ESD surge protection for each output
Power +9V up to +24V DC via Terminal Block or DC-Connector
Up to 2.4 A per port, total output power max. 27 W (5.4A@5V)
Automatic recognition the data transfer rate for the attached external devices
Includes wall mount kit and DIN-Rail Kit
Compact industrial design
Rugged metal case
LED indicators for power supply and connection status
Chipset: VIA VL817S
Packaging contents:EX-11244HMS, USB 3.2 Gen 1 cable 2.0m, DIN-Rail Kit, Wallmount Kit, Manual
EX-1163
4 Port USB 2.0 HUB, plastic housing incl. power supply
With the EX-1163 you can extend from one USB 2.0 port to four USB 2.0 ports. It’s possible now to connect up to four external USB 2.0 peripherals devices to one USB 2.0 port from the Notebook or Desktop Computer. He it’s very compact and robustly.
USB 2.0 HUB with four USB 2.0 ports
Automatic recognition the data transfer rate for the attached external peripheral devices
Support all USB 2.0 compatible devices
Power from the USB port (Bus-Power)
Chip-Set: NEC uPD720112
Packaging contents:EX-1163, USB 2.0 cable (2.0 meter), Wall– or table top holder, Manual
EX-1181HMS
Smallest 4-Port USB 3.2 Gen 1 Metal HUB with 15KV ESD Surge Protection, A-Ports
The rugged industrial-grade EX-1181HMS is the smallest USB 3.2 Gen 1 metal hub for up to four end devices. The hub provides four USB 3.2 Gen 1 downstream ports with 15KV ESD surge protection. It is thus possible to connect up to four external USB peripherals to one USB 3.2 Gen 1 port from the computer in a 19" rack. By supplying power through the two-wire terminal block connector, 1A can be provided to each USB port. It supports SuperSpeed USB 3.2 Gen 1 data transfer rate up to 5Gbps and is backward compatible to USB 1.1. The EX-1181HMS can be powered by USB bus power or via a two-wire terminal block connector. The HUB meets the special requirements of industrial applications.
USB 3.2 Gen 1 Metal HUB with 4 Ports
15KV ESD Surge Protection for all 4 Ports
Protection of Devices against voltage fluctuation
Power +7V-48V DC over the Terminal Block
Power supply optionally also from the USB-Bus +5V (Bus-Power)
Easy installation with the included DIN-Rail Kit
Automatic recognition the data transfer rate for the attached external devices
Supports 1A power for each output simultaneously
Automatic detection of input polarity on the current terminal block
Rugged Metal Case
1x LED Power-Indicator
Internal jumper for individual control of power supply:- ENA = bus power operation possible- DIS = operation with power supply only (self power)
Packaging Contents:EX-1181HMS, USB 3.2 Gen 1 Cable, DIN-Rail Kit, Wall Mounting Bracket, Manual
EX-1110HMVS-PL
10-Port USB 3.2 Gen 1 HUB Board with 15KV ESD Surge Protection
The USB 3.2 Gen 1 Hub Board EX-1110HMVS-PL is a fully functional industrial USB 3.2 hub with ten downstream ports for integration into custom devices, assemblies or enclosures. It is ideal for embedded systems, kiosks, industrial automation and other specialised applications requiring multiple USB ports.
USB 3.2 Gen 1 hub with ten downstream ports
USB 3.2 Gen 1 data transfer rate up to 5 Gbps
Backward compatible with USB 3.1, 3.0, 2.0, 1.1
15KV ESD surge protection for each output
Protects end devices from voltage fluctuations
Power supply +7V to +24V DC via Terminal Block
Optional power supply from USB bus +5V (bus power)
Automatic detection of data transfer rate of connected peripheral devices
Automatic detection of input polarity on power Terminal Block
Up to 1.5A per port, total output power max. 75 W
Supports USB battery charging V1.2
LED power indicator
Chipset: Genesys
Two jumpers for individual mode control (data and power):
Bus power jumper:
ENA = bus power operation possible
DIS = operation with power supply only (self power)
Host control jumper:
ON = Power supply independent of host PC
HOST = Power supply only when host PC is switched on
Packaging contents:EX-1110HMVS-PL, Terminal Block
EX-1116HMVS
16-Port USB 3.2 Gen 1 Metal HUB with 15KV ESD Surge Protection, A-Ports
The rugged, industrial-grade EX-1116HMVS hub provides sixteen bolt-on USB 3.2 Gen 1 downstream ports with 15KV ESD surge protection. It is thus possible to connect up to sixteen external USB peripherals to one USB 3.2 Gen 1 port from the computer in a 19" rack. It supports SuperSpeed USB 3.2 Gen 1 data transfer rate of up to 5Gbps and is backward compatible to USB 1.1. The included USB 3.2 Gen 1 cable with can be attached to the EX-1116HMVS with thumbscrews without a screwdriver. The EX-1116HMVS must be powered via a DC Jack (+12V to +24V), or via a two-wire terminal block connector (+12V to +24V). The HUB meets the special requirements of industrial applications.
USB 3.2 Gen 1 Metal HUB with 16 Ports
15KV ESD Surge Protection for all 16 Ports
Protection of devices against voltage fluctuation
Power +12V up to +24V DC over the DC-Connector or Terminal Block
Easy installation with the included DIN-Rail Kit
Automatic recognition of the data transfer rate for the attached external devices
Supports 1.5A power for each output simultaneously
Supports BC v1.2: SDP/CDP/DCP Charging Modes
Automatic detection of input polarity on the terminal block
Rugged metal case
1x LED Power-Indicator
2x LED Active-Indicator USB 3.2 Gen 1 Upstream B-Port
Packaging Contents:EX-1116HMVS, USB 3.2 Gen 1 Cable, DIN-Rail Kit, 2x Mounting Angle, Manual
EX-1110HMVS
10-Port USB 3.2 Gen 1 Metal HUB with 15KV ESD Surge Protection, A-Ports
The rugged, industrial-grade EX-1110HMVS provides ten bolt-on USB 3.2 Gen 1 downstream ports with 15KV ESD surge protection. It is thus possible to connect up to ten external USB peripherals to one USB 3.2 Gen 1 port from the computer in a 19" rack. It supports SuperSpeed USB 3.2 Gen 1 data transfer rate of up to 5Gbps and is backward compatible to USB 1.1. The included USB 3.2 Gen 1 cable with can be attached to the EX-1110HMVS with thumbscrews without a screwdriver. The EX-1110HMVS can be powered with USB bus power or via a two-wire terminal block connector (+7V to +24V). The HUB meets the special requirements of industrial applications.
USB 3.2 Gen 1 Metal HUB with 10 Ports
15KV ESD Surge Protection on all 10 Ports
Protection of Devices against voltage fluctuation
Power +7V up to +24V DC over the Terminal Block
Power supply optionally also from the USB-Bus +5V (Bus-Power)
Easy installation with the included DIN-Rail Kit
Automatic recognition of the data transfer rate for the attached external devices
Supports 1.5A power for each output simultaneously
Support BC v1.2: SDP/CDP/DCP Charging Modes
Automatic detection of input polarity on terminal block
Rugged Metal Case
1x LED Power-Indicator
Chipset: Genesys
Internal jumper for individual control of power supply:- ENA = bus power operation possible- DIS = operation with power supply only (self power)
Packaging contents:EX-1110HMVS, USB 3.2 Gen 1 Cable, DIN-Rail Kit, Manual
EX-1187HMVS-2
7 Port USB 3.2 Gen 1 HUB with 15KV ESD Surge Protection (DIN-Rail Kit)
The rugged and industrial-grade EX-1187HMVS-2 is a USB 3.2 Gen 1 metal hub for up to seven end devices. The hub provides seven screwable USB 3.2 Gen 1 downstream ports with 15KV ESD surge protection. It is thus possible to connect up to seven external USB peripherals to one USB 3.2 Gen 1 port from the computer in a 19" rack. The included USB 3.2 Gen 1 cable can be attached to the EX-1187HMVS-2 with thumbscrews without a screwdriver. The EX-1187HMVS-2 can be powered via a DC Jack (+7V to +48V) or via a two-wire terminal block connector (+7V to +48V). The HUB meets the special requirements of industrial applications.
USB 3.2 Gen 1 Metal HUB with 7 Ports
15KV ESD Surge Protection for all 7 Ports
Protection of Devices against voltage fluctuation
Power +7V up to +48V DC over the Terminal Block
Easy installation with the included DIN-Rail Kit
Automatic recognition of the data transfer rate for the attached external devices
Supports 900mA power for each output simultaneously
Automatic detection of input polarity on the current terminal block
Rugged Metal Case
1x LED Power-Indicator
Chipset: Genesys
Packaging contents:EX-1187HMVS-2, USB 3.2 Gen 1 cable, DIN-Rail Kit, Manual
EX-12290HMS
10 Port USB 3.2 Gen 2x1 Metal HUB with 4x USB-C and 6x USB-A 3.2 Gen 1, for table, wall and DIN-Rail mounting
The EX-12290HMS is a rugged metal USB 3.2 Gen 2x1 hub for up to ten devices that can be mounted on a wall or DIN-rail. It connects to the host PC via a USB-C cable and provides four USB-C 3.2 Gen 2x1 ports and six USB-A 3.2 Gen 1 ports for end devices. The USB-C ports offer excellent performance of up to 10Gbps (SuperSpeed USB 10Gbps), while the USB-A ports transfer data at up to 5Gbps (SuperSpeed USB 5Gbps). Up to 2.5A per port with a maximum of 64W is available from the external power supply. This makes it easy to charge iPhone, iPad, smartphones and tablets. Power is supplied via the plug-in power supply unit supplied or an optionally available DIN-Rail power supply unit (self-power).
USB 3.2 metal HUB with 4x USB-C Gen 2x1 and 6x USB-A Gen 1 downstream
15KV ESD surge protection for each output
Power +9V up to +24V DC via Terminal Block or DC Jack
Up to 2.4A per port, total output power max. 64W
Automatic detection of the data transfer rate of connected peripherals
Includes wall mount kit and DIN-Rail Kit
Compact industrial design
Rugged metal case
LED indicators for power supply and connection status
Packaging contents:EX-12290HMS, Power Supply (24V/3A), USB 3.2 Gen 2x1 Cable (screw lock) 1m, DIN-Rail Kit, Wall Mounting Brackets, Manual
New
EX-12270HMS
10-port USB 3.2 Gen 2 metal hub with 10x USB-C connector, 79.5W
The rugged, industrial-grade EX-12270HMS is a metal USB 3.2 Gen 2x1 hub for up to ten devices that can be mounted on a wall or on a DIN-Rail. It connects to the host PC via a USB-C cable and provides ten USB-C 3.2 Gen 2x1 ports for end devices with outstanding performance of up to 10Gbps (SuperSpeed USB 10Gbps). Using the external power supply, the hub provides up to 2.4A per port with a maximum output of 79.5W. This makes it easy to charge iPhones, iPads, smartphones and tablets. Power is supplied via the included power supply or an optional DIN-Rail power supply (self-powered).
USB 3.2 metal HUB with 10x USB-C Gen 2x1 downstream
15KV ESD protection for each output
Power supply +9V to +24V DC via terminal block or DC-jack
Up to 2.4A per port, total output power max. 79.5W
Supports USB battery charging V1.2
Can also be used as a USB charger without connection to the host PC
Automatically detects the data transfer rate of connected peripherals
Wall bracket and DIN-Rail kit included
Rugged metal housing with compact industrial design
LED indicators for power and link Status
Chipset: VL822-Q7
Packaging contents:EX-12270HMS, Power Supply (24V/4A), USB 3.2 Gen 2x1 Cable (screw lock) 1m, DIN-Rail Kit, Wall mounting brackets, Manual
EX-1171
7 Port USB 2.0 HUB, plastic housing incl. power supply
With the EX-1171 you can extend from one USB 2.0 port to seven USB 2.0 ports. It’s possible now to connect up to seven external USB 2.0 peripherals devices to one USB 2.0 port from the Notebook or Desktop Computer. He it’s very compact and robustly.
USB 2.0 HUB with seven USB 2.0 ports
Automatic recognition the data transfer rate for the attached external peripheral devices
Support all USB 2.0 compatible devices
Power from the USB port (Bus-Power)
Chipset: NEC uPD720113
Packaging contents:EX-1171, USB 2.0 cable 2.0m, Power Supply Wall- or table top holder, Manual
EX-6683
FireWire 1394A 6 Port Metal HUB (Repeater)
The EX-6683 can be use for a 6 Port FireWire 1394A HUB or for a Active Extend-ed Box. With the metal case the EX-6683 it s very robust and optimal for industrial application.
6 Port FireWire 1394 Hub
Hot Plug and Play
Support on the P1394 Bus
Included 12V / 3A power supply
EX-6684
FireWire 1394B with 8 ports Metal HUB
The EX-6684 can be use for a 8 Port FireWire 1394B HUB or for a Active Extended Box. With the metal case the EX-6684 it s very robust and optimal for industrial application.
8-Port FireWire 1394B HUB
Hot Plug and Play
Supports power on the P1394 bus
Packaging contents:EX-6684, FireWire cable 9-pin, Power Supply 12V/1.5A, Manual
EX-1163V
4 Port USB 2.0 HUB, plastic housing, screw lock cable
With the EX-1163V you can extend from one USB 2.0 port to four USB 2.0 ports. It’s possible now to connect up to four external USB 2.0 peripherals devices to one USB 2.0 port from the Notebook or Desktop Computer. He it’s very compact and robustly. With the USB cable EX-K1542V (1.8 meter) A-male to B-male and the power supply you can fix the connector with screw. The cable it’s fix and can’t be disconnect any more by him self. The power connector it’s also screw able.
USB 2.0 HUB with four USB 2.0 ports with screw lock
Automatic recognition the data transfer rate for the attached external peripheral devices
Support all USB 2.0 compatible devices
Power from the USB port (Bus-Power)
Chipset: NEC uPD720112
Packaging contents:EX-1163V, USB 2.0 cable (1.8 meter), Wall- or table top holder, Manual
EX-1166HMV
USB 2.0 Metal-Hub with 4 ports, Cable can screw lock
With the EX-1166HMV you can extend from one USB 2.0 port to four USB 2.0 ports. It’s possible now to connect up to four external USB 2.0 peripherals devices to one USB 2.0 port from the Notebook or Desktop Computer. He it’s very compact and robustly. With the USB cable EX-K1542V (1.8 meter) A-male to B-male and the power supply you can fix the connector with screw. The cable can’t be disconnect any more by him self. The EX-1166HMV you can fix to the wall or optional you can install the EX-1166HMV with the product EX-6099 (DIN-Rail-Kit) in a 19 inch Rack.
USB 2.0 HUB with four screw lock USB 2.0 ports
Automatic recognition the data transfer rate for the attached external peripheral devices
Support all USB 2.0 compatible devices
Power from the USB Bus (Bus Power) or power supply with screw lock
Chipset: NEC uPD720112
Packaging contents:EX-1166HMV, USB 2.0 cable 2.0m, 5V/4A Power supply, Manual
EX-1177HMVS
7 Port USB 2.0 Metal HUB (DIN-Rail) and 15KV ESD Surge Protection
The rugged, industrial-grade EX-1177HMVS offers seven screw lock USB 2.0 Downstream ports with 15KV ESD Surge Protection. It is possible to connect up to seven external USB 2.0 peripheral devices to one USB 2.0 port in a 19-inch rack. With the USB cable EX-K1542V (1.8 meter) A-male to B-male you can fix the connector with screw. He can be used for automation– and office applications. The EX-1177HMVS fulfils the special requirements of industrial applications.
USB 2.0 HUB with seven screw lock Downstream USB 2.0 ports
15KV ESD Surge Protection for each port
Support protection of devices against voltage fluctuation
Power +7V up to +24V DC from the Terminal Block
Easy installation with the included DIN-Rail Kit
Compact industrial design
Automatic detects the data transfer rate for the attached external peripheral devices
Optional power over USB port +5 Volt (Bus-Power)
Chipset: Terminus FE 2.1
Internal jumper for individual control of power supply:- ENA = bus power operation possible- DIS = operation with power supply only (self power)
Packaging contents:EX-1177HMVS, USB 2.0 cable 2.0m, DIN-Rail Kit, Manual
EX-1635
USB 3.2 Gen 1 (3.0) Card Reader and HUB with 3 Ports
The EX-1635 USB 3.0 Card Reader for SD / SDHC, Memory Stick, ect. cards include also a USB 3.0 HUB with three additional ports. The EX-1635 is Plug-and-Play and can install without driver.
USB 3.0 Card Reader
USB 3.0 HUB with 3 ports
Built-in All in One Card Reader for memory cards
Support SD / SDHC, Memory Stick, TF, M2, MMC
LED Indicators for power status
Power from USB Bus (Bus Power) or power supply
Support “hot swapping” of all your USB devices
Compatible with USB 1.1, USB 2.0 and USB 3.0 devices
Compliant to USB 3.0 specification Rev. 1.0
EX-1167
Internal 7 Port USB 3.2 Gen 1 HUB for 3.5-inch front-bay
Der EX-1167 erweitert einen USB 3.2 Gen 1 Ausgang (früher genannt USB 3.0) von Desktop Rechner um sieben weitere USB 3.2 Gen 1 Ports. Er wird in einen freien 3.5“ Front-Bay Schacht vom PC eingebaut. Es ist somit möglich bis zu sieben externen USB 2.0 oder 3.2 Gen 1 Peripheriegeräte an einen USB 2.0 oder 3.2 Gen 1 Port vom Desktop Rechner anzuschließen.
Interner USB 3.2 Gen 1 HUB mit 7 Ports
Automatische Erkennung der Datentransferrate für die angeschlossenen Peripheriegeräte
Unterstützt alle USB 1.1 bis 3.2 Gen 1 kompatiblen Peripheriegeräte
Unterstützt 900mA USB Bus Power für jeden Ausgang
Stromversorgung: vom USB Bus (Bus Power) oder PC-Netzteil
Chipsatz: VIA VL810
Lieferumfang:EX-1167, Adapter für Mainboard Anschluss zu 2x USB-A Buchse, Handbuch
EX-1174
Internal 4 Port USB 2.0 Metal HUB for 3.5" Bay
The EX-1174 expand one USB 2.0 pin header connector on the motherboard or an expansion card to four USB 2.0 A-Ports. The EX1174 will be install in to a 5.25-inch and 3.5-inch bay from your computer system. It’s possible now to connect up to four external USB 2.0 peripherals devices to one USB 2.0 pin header connector from the Desktop Computer.
Internal USB 2.0 HUB with four USB 2.0 ports
Automatic recognition the data transfer rate for the attached external peripheral devices
Support all USB 2.0 compatible devices
Power from the computer power supply
Support 3.5-inch and 5.25-inch Front Bay
Metal case
Chip-Set: Cypress
EX-1187HMVS
7 Ports USB 3.2 Gen 1 Metal HUB with 15KV ESD Surge Protection (DIN-Rail)
The rugged, industrial-grade EX-1187HMVS USB hub, with seven USB 3.2 Gen 1 (previously called USB 3.0) screw-in outputs and 15KV ESD surge protection, can be installed on a wall or on a support rail. It connects to a computer or server with the included USB 3.2 Gen 1 cable. It can be powered with USB bus power or via a two-wire terminal block connector (+7V to +48V).
USB 3.2 Gen 1 Metal HUB with four Downstream ports
15KV ESD Surge Protection for all ports
Power +7V up to +48V DC over the Terminal Block
Power supply optionally also from the USB-BUS +5V (Bus-Power)
Easy installation with the included DIN-Rail Kit
Compact industrial design
Automatic recognition of the data transfer rate for the attached external devices
900mA current on all 7 ports
Automatic detection of input polarity on the current terminal block
Rugged metal case
1x LED Power Display
Packaging contents:EX-1187HMVS, USB 3.2 Gen 1 cable 1.5m, DIN-Rail Kit, Manual